之前,如果没有 ?> 就直接放最后)===== // 1) Google Search Console 验证标签 add_action( 'wp_head', function () { echo '' . "\n"; }, 1 ); // 2) 匿名访问的 HTML 加 CDN 缓存头(浏览器不缓存,CDN 缓存 1 小时) add_filter( 'wp_headers', function ( $headers ) { if ( is_admin() || is_user_logged_in() ) { return $headers; } $headers['Cache-Control'] = 'public, max-age=0, s-maxage=3600, stale-while-revalidate=86400'; return $headers; }, 20 ); // ===== 粘贴结束 ===== Quality Control | ISO 9001 CNC Machining | Hanz

Dongguan, Guangdong, China · ISO 9001 quality system

Quality

Quality control that starts before the first cut

ISO 9001 quality system, drawing review, first article inspection, in-process checks and final reports for machined and cast parts.

  • ISO 9001 quality system
  • Quotes within hours
  • Prototype to production

Approach

Inspection cannot fix a bad setup

The most expensive quality problem is the one discovered after the parts are finished. Our process is built to catch it earlier: review the drawing, agree the inspection method, verify the first article, then check the features that can drift during the run.

We work to an ISO 9001 quality management system. That means documented procedures, traceable material, calibrated inspection tools and a corrective action path when something goes wrong.

  • Drawing and tolerance review
  • Material certificates
  • First article inspection
  • In-process checks
  • Final dimensional report
  • Corrective action on nonconformance

Process

The quality plan for a typical order

Drawing review

Datums, tolerances, finishes and inspection access are checked before quoting.

Material verification

Grade and condition are confirmed against the certificate before machining.

First article

The first part is measured against the drawing and approved before the batch continues.

In-process checks

Critical dimensions are checked as the batch runs, not only at the end.

Final inspection

Parts are checked, counted, packed and shipped with the agreed documentation.

Documentation

What we document

Documentation depends on what your assembly and your auditor need. At minimum, we can supply a dimensional report for the features agreed at quoting and a mill certificate for the material. First article reports and photos are available on request.

If your part needs PPAP-style documentation, a specific inspection sheet or a certificate of conformance, tell us before the order. Building the paperwork into the plan is cheaper than reconstructing it afterward.

  • Dimensional inspection report
  • Material certificate
  • First article report
  • Certificate of conformance
  • Photos before shipment
  • Nonconformance report when applicable
Quality inspection of a machined component

Measurement

Measured the way the drawing says

A dimension is only meaningful with a measurement method. If a callout needs a specific datum, a gauge or a particular surface, we agree that method before production. If the drawing asks for something that cannot be measured as shown, we raise it early.

This is also why we ask which dimensions control fit and function. Those get the attention; the rest get sensible general tolerances.

  • Datum scheme agreed
  • Calibrated inspection tools
  • Critical features checked in process
  • Reports matched to drawing revision
  • Traceability by lot
  • Photos of non-cosmetic features

Escalation

When something goes wrong

No shop is perfect. What matters is what happens next. If a part is out of specification, we tell you, explain the cause, propose containment and correct the process before the next run.

We would rather ship a smaller batch on time and tell you the truth about the rest than hide a problem in a box.

FAQ

Questions buyers ask before the first order

Are you ISO 9001 certified?

We operate an ISO 9001 quality management system. Certificates and scope documents are available on request.

Can you provide a first article inspection report?

Yes. Ask for it at quoting so the inspection plan and the report format are agreed before production.

Do you provide material certificates?

Yes. Mill certificates are available for the material used in your order.

What happens if parts are out of tolerance?

We inform you immediately, contain the affected parts, investigate the cause and agree on rework or replacement before shipping.

Can I specify my own inspection sheet?

Yes. Send the form with the order and we will complete it for the agreed features.

Start a project

Send your drawings. Get a quote in hours.

Upload CAD files or send a sketch with material, quantity and finish. Our engineers reply with pricing, DFM notes and a lead time, usually within one business day.

Request a quote Email engineering

Typical reply: within 1 business day

Call Get a quote