Overview
The short version
A tolerance is the amount a dimension is allowed to vary. Tighter tolerance means more time, more inspection and sometimes a different machine and fixture. The cheapest tolerance is the one the part actually needs.
Most machining quotes are driven less by the nominal geometry than by a handful of tight callouts. If you can identify the two or three dimensions that control fit and function, and leave the rest at general tolerance, the price usually drops.
Ranges
Typical tolerance ranges by process
| Process | Typical range | Notes |
|---|---|---|
| CNC milling (general) | About +/-0.1 mm | Depends on feature size, material and fixture |
| CNC milling (precision) | About +/-0.02 mm | Requires tighter setup, temperature control and inspection |
| CNC turning | About +/-0.05 mm general, tighter on diameters | Roundness and taper matter as much as diameter |
| Swiss machining | Tight on small diameters | Depends on part length and support |
| Aluminum die casting | About +/-0.2 to 0.5 mm | Machining is added for critical features |
| Surface finish | Ra 3.2 down to Ra 0.8 um | Polishing or lapping can go finer |
These are typical industry ranges, not a promise. Always confirm the specific callouts with your supplier before production.
Cost
Why tight tolerance gets expensive fast
At a certain point, tolerance stops being a machining problem and becomes a measurement, temperature and handling problem. The machine may be capable, but the part moves when it is clamped, the coolant changes the temperature, or the gauge cannot repeat the reading.
That is why the price curve is not linear. Going from +/-0.1 to +/-0.05 may add a little. Going from +/-0.02 to +/-0.005 can add a second operation, a different inspection method and a lot of scrap risk.
- Tighter tolerance means slower feeds and more passes
- More inspection time per part
- Higher scrap risk
- Special fixturing may be required
- Temperature control can matter
- Some features cannot be measured as drawn
GD&T
GD&T in plain language
Geometric dimensioning and tolerancing controls the relationship between features, not just the size. Flatness says a surface has to be flat regardless of its thickness. Position says a hole has to be in the right place relative to a datum. Runout says a surface has to rotate true.
The value of GD&T is that it describes function. The risk is that it is easy to copy a tight callout from an old drawing without knowing what it costs. If a control is not tied to how the part works, question it.
- Flatness: how flat a surface must be
- Perpendicularity: how square to a datum
- Position: where a feature may sit relative to datums
- Concentricity / runout: rotating relationship
- Profile: how closely a surface follows the model
- Datum selection: what the part is measured from
Controls
GD&T controls and what they usually cost
| Control | What it constrains | Cost driver |
|---|---|---|
| Flatness | Surface form | Fixture and material stress |
| Parallelism | Two surfaces relative to each other | Setup and measurement |
| Perpendicularity | Squareness to a datum | Machine geometry and fixturing |
| Position | Location of holes and features | Drilling strategy and inspection |
| Profile | Surfaces against a 3D model | 5-axis machining and scanning |
| Runout | Rotating surfaces | Turning setup and centers |
Specifying
How to specify tolerances well
Put a general tolerance in the title block, then call out only the features that need more. Use datums that reflect how the part is assembled, not just how it is machined. Mark cosmetic surfaces so the shop knows where to spend time.
If you are unsure what a feature needs, ask for two quotes: one at the drawing tolerance and one at a relaxed tolerance. The difference tells you what the requirement is worth.
- General tolerance in the title block
- Per-feature callouts only where needed
- Datums tied to assembly
- Cosmetic vs functional surfaces marked
- Material and finish specified
- Inspection method agreed
Stack-up
A tolerance stack-up in one paragraph
Define the gap
Start with the assembly dimension you actually need, such as a gap or an interference fit.
List the contributors
Every part dimension, fixture offset and process variation that affects the gap.
Add the variation
Worst-case adds every tolerance; statistical methods assume distributions.
Allocate
Give the tightest tolerance to the feature that is cheapest to control, not the one that is easiest to draw.
Measurement
Inspection is part of the tolerance
A tolerance that cannot be measured repeatably is not a real tolerance. Calipers, micrometers, height gauges and CMMs all have limits, and the method has to match the callout.
If a print requires a measurement the supplier cannot perform, the honest answer is to agree a different method before the order, not to ship a number that looks right.